Lytron uses compressor-based refrigeration in its Kodiak and large capacity lines of recirculating chillers. The basics of compressor-based refrigeration are explained below.

Fundamental Physical Principles

When trying to understand how a compressor based cooling system works, you must keep three physical phenomena in mind:

  1. When a gas is compressed, its temperature increases. Conversely, when it is expanded, its temperature decreases. This is one of the ramifications of the First Law of Thermodynamics.

  2. The temperature of a pure liquid remains constant as it boils or condenses. We have all witnessed this phenomenon in our kitchens. If you measure the temperature of water as it boils, the temperature remains constant at 212°F or 100°C as long as liquid water is present. Also, when gases are condensed, the system temperature remains constant until all the gas converts to a liquid.

  3. Finally, a significant amount of energy is required for a fluid to undergo phase change. As an illustration, more energy is needed to completely boil a given amount of water than to take that same quantity of water from 32°F to 211°F. This means that a significant amount of energy can be stored and then released just during a phase change.

The Refrigeration Cycle

As the name states, the refrigeration cycle is a continuous process. Refrigerant moves from the compressor to the condenser, through a metering device, to an evaporator, and then the cycle repeats (see figure 1).

The compressor does exactly as its name says: it compresses the refrigerant. The compressor receives low pressure gas from the evaporator and converts it to high pressure gas. As mentioned earlier, as the gas is compressed, the temperature rises.

The hot refrigerant gas then flows to the condenser. The condenser is a heat exchanger that uses a colder fluid, typically ambient air, to cool the refrigerant. As refrigerant flows through this heat exchanger, it condenses to a hot liquid. Liquid refrigerant exits the condenser and flows to the system's metering device.

The metering device can be an expansion valve or a capillary tube and is used to create a pressure drop. As mentioned earlier, the temperature and boiling point of liquids decrease as the pressure decreases. Some refrigerant liquid vaporizes and the temperature of the liquid-gas mixture drops. The cool refrigerant then flows to the evaporator.

The evaporator is another heat exchanger that allows heat to move between the medium we wish to keep cool, called the heat source, and the refrigerant. In a chiller, the heat source is the cooling fluid, which flows into your equipment. The refrigerant enters the evaporator as a low temperature gas-liquid mixture. By design, the temperature of the heat source is always higher than the refrigerant's boiling point. In the evaporator, the refrigerant vaporizes as it absorbs heat from the heat source. As our "Fundamental Physical Principles #2" states the refrigerant's temperature remains constant as it vaporizes. The refrigerant then exits the evaporator as a gas, enters the compressor and the cycle starts again.

Of course we have simplified the process considerably. For more information, we recommend any basic engineering thermodynamics book, such as Introduction to Chemical Engineering Thermodynamics, by J.M Smith, H.C. Van Ness, M.M. Abbott, Mcgraw-Hill Chemical Engineering Series, 1996.


Product Selector

Use the Lytron selector tool to easily determine the best cooling component or system for your application.

Request Quote

If you need a custom designed unit for large OEM quantities please request a quote or call +1-781-933-7300

Shop Online

Know your Lytron product name or part number?

Visit Lytron Direct

Lytron Inc,

55 Dragon Court,

Woburn, MA

Lytron specializes in custom liquid cooling solutions. We design and manufacture cold plates, chassis, chillers, cooling systems, and heat exchangers for some of the most demanding thermal management applications. Learn More.

We use cookies to measure traffic and help improve our website and online portal. You can learn more about our use of cookies and how to change your browser settings in order to avoid cookies by viewing our Privacy Policy. By continuing to use this site without changing your settings, you agree to our use of cookies. You can change your settings at any time.